ZGB. Dash Installation

                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                         


Other Links





Evolution Orange

2000 Miata LS

Dash Installation


I re-installed the dash today.  It went much quicker than I thought it would.  I took a lot of pictures of each step so I will be able to remove it much quicker next time.


First I had to lift the dash into the car and center it without breaking or pinching anything.  I was able to get it into place by myself without much trouble.  I did have to pull the antenna lead out of the way and back toward the heater core to keep from pinching it.


MM 00 EVO Dash Installation 1



MM 00 EVO Dash Installation 2



I was advised to start all the nuts and bolts before tightening any of them down.  This was good advice.  I had to shift the dash several times to start bolts, but all of them went in without issue.  Here are their locations.


MM 00 EVO Dash Installation 3



MM 00 EVO Dash Installation 4



MM 00 EVO Dash Installation 5



MM 00 EVO Dash Installation 6



MM 00 EVO Dash Installation 7



Once all of them were in, I tightened them all and replaced the covers.


MM 00 EVO Dash Installation 8



MM 00 EVO Dash Installation 9



MM 00 EVO Dash Installation 10



MM 00 EVO Dash Installation 11



MM 00 EVO Dash Installation 12


MM 00 EVO Dash Installation 13



Then I worked on bolting the steering column back into place.  I first put one bolt in to support the column after positioning the two rear mounting points.  The nuts were installed and finally the last bolt.


MM 00 EVO Dash Installation 14



MM 00 EVO Dash Installation 15



MM 00 EVO Dash Installation 16



MM 00 EVO Dash Installation 17



I installed the plastic cover over the steering shaft knuckle.  It just clipped on.


MM 00 EVO Dash Installation 18



MM 00 EVO Dash Installation 19



MM 00 EVO Dash Installation 20



MM 00 EVO Dash Installation 21



The wiring connections were next.  Starting on the driver's side, the large white connector had to be connected and attached to the dash frame.


MM 00 EVO Dash Installation 22



MM 00 EVO Dash Installation 23



MM 00 EVO Dash Installation 24



The trunk release was reattached.  It goes into the slot on the plastic and the nut holds it in place from behind.



MM 00 EVO Dash Installation 25



Now I reattached the fuse block.  It slips into a slot on the upper mount and two screws hold it in place.  The two screws are threaded to fit into blind nuts so I was careful not to use the screws meant for nylon inserts.


MM 00 EVO Dash Installation 26



This large black connector had to be reattached to the dash frame.


MM 00 EVO Dash Installation 27



MM 00 EVO Dash Installation 28



That finished the connectors under the dash on the driver's side.


I moved to the passenger's side and started reconnecting things under the dash.


First was this wire bundle on a white zip tie type anchor.  It attached to the metal just above where the glove box fits.


MM 00 EVO Dash Installation 29



Then the connectors on the far right side were connected.  There is the large one with brown foam around it and the white one that connects at the fan.  The yellow one is for the airbag.  I installed it later.


MM 00 EVO Dash Installation 30



MM 00 EVO Dash Installation 31



MM 00 EVO Dash Installation 32



Next was installing the A/C and heater controls.  There are three control cables that are snaked back into the dash.  The longest one is fed up toward the top of the fan unit.  The other two go to each side of the heater core assembly.


Once the unit is close to in, the connectors must be reattached.  There is one to the A/C switch, one to the defroster switch and a large one in the middle for the fan switch.  The cable that they are attached to has an anchor that attaches at the rear of the control assembly.






The control cables all attached by slipping the end loop over a post and pushing the cable cover back into the clip.  I used the old marks to position the cable cover into the clip.  They may need adjustment later.


MM 00 EVO Dash Installation 35



MM 00 EVO Dash Installation 36



MM 00 EVO Dash Installation 37



Now I installed my white faced instrument cluster.  It has three connectors to plug into the back and it is held into place with four screws.  Then the instrument cluster hood snapped on.  The steering column cover lower half is held into place with two screws for a nylon insert and the one in the rear is a threaded screw for a blind nut.  The top half snaps on.


MM 00 EVO Dash Installation 38



MM 00 EVO Dash Installation 39



MM 00 EVO Dash Installation 40



The passenger's side airbag was installed with two bolts and two nuts.  The connector is the yellow one mentioned earlier.   I also installed the glove box after connecting the yellow connectors together.  The glove box has a pin on the lower left side and a clip on the lower right that snaps onto a pin.  The two stops had to be positioned before snapping it on.


MM 00 EVO Dash Installation 41



MM 00 EVO Dash Installation 42



Now I installed the pillar covers.  Since I cracked the passenger's side cover,  I got another one from Flyin' Miata out of a parts car.



MM 00 EVO Dash Installation 43



I even installed some louvered vents from a Mitsubishi Eclipse.  I love those.  Now the dash is  almost finished.  


I have purchased a wood grain surround and it should be here this week. I will install it once it arrives.  It will match the wood steering wheel, e-brake handle and shifter knob that I already have.  I will use the original steering wheel until the painting is finished.


I also am going to replace the clock spring since the airbags deployed.  Tom at The Parts Group is sending me one.  Thanks again Tom!


This job is not bad after learning all the attachment points and connections to remove.  It does have many steps, but I would do it again if I needed to.  I will always come back to this to see the pictures so I can make the job go smoother.  


I guess my success will be measured when it is powered up and everything works!

 

 


Vendor Links







Comments